Hwacheon Hi-M1300

Mock-up & engraving vertical machining center

Hi-M Series

Built to order. Ask for lead time.

Overview

1,300 x 800 mm travel, 24,000 rpm mock-up and engraving machining center

The Hi-M1300 is a double column vertical machining center from Hwacheon's Hi-M Series, built for mock-ups, engraving and mold work. It carries a grease-lubricated BT-30 built-in spindle at 24,000 rpm, with a 30,000 rpm version, and a 16-tool ATC. Travel is 1,300 / 800 / 400 mm over a 1,300 x 800 mm table, with 25 / 25 / 20 m/min rapids. It comes with an around cover as standard and a full cover as an option.

Guides: when an HMC makes sense and choosing your first or next VMC

At a glance

X / Y / Z travel: 51.2 / 31.5 / 15.7 in
Table size: 51.2 x 31.5 in
Spindle: BT-30, 24,000 rpm (30,000 rpm option)
Tool capacity: 16 tools
Control: Siemens 828D (FANUC 0i-MF option)

Features

01Built-in high-frequency spindleThe motor is built into the spindle shaft with no parts transferring power between them, which cuts vibration, noise and power loss at high speed. The Hi-M1300 runs a BT-30 spindle to 24,000 rpm, or 30,000 rpm as an option, with grease-lubricated bearings.
02Double column frameThe portal-type double column frame uses Meehanite castings in the main frames and was designed with 3D modeling and FEM analysis for structural stability.
03Ball screws fixed at both endsEach axis runs precision ball screws fixed at both ends on wide LM guides (2-rail, 6-block). Cutting feed is 1 to 10,000 mm/min.
0416-tool ATCThe fixed-address rotational ATC holds 16 tools up to Ø16 mm, 200 mm long and 3 kgf. Tool change takes 22 seconds tool to tool and 25 seconds chip to chip, and an auto door on the ATC keeps chips out.
05SIEMENS or FANUC controlSIEMENS-828D is standard and FANUC 0i-MF Plus is optional. Conversational programming is available as ShopMill on SIEMENS or Manual Guide i on FANUC, both as options.
06Tool length measurement optionAn optional tool length compensator (Renishaw, Blum or Metrol) measures tool length and diameter during the run and flags damaged tools. A work probe is not available because the spindle does not support orientation.

Specifications

Item		Hi-M1300 series
Item		Hi-M1300 24K	Hi-M1300 30K
Travel
X-axis strokein	in	51.2	51.2
Y-axis strokein	in	31.5	31.5
Z-axis strokein	in	15.7	15.7
Table surface to spindle nosein	in	2.0 ~ 17.7	2.0 ~ 17.7
Table
Table sizein	in	51.2 x 31.5	51.2 x 31.5
Max loading capacitylb	lb	661	661
T-slot (W x P / no. of slots)in	in	0.63 x 4.9 / 5ea	0.63 x 4.9 / 5ea
Spindle
Max spindle speedrpm	rpm	24,000	30,000
Spindle motorHP	HP	8.0 (Opt.: 16.8)	8.0 (Opt.: 16.8)
Spindle taper		BT-30	BT-30
Spindle type		Built-in	Built-in
Spindle lubrication		Grease	Grease
Spindle cooling		Coolant cooling (Water Chiller)	Coolant cooling (Water Chiller)
Feedrate
Rapid traverse (X / Y / Z)ipm	ipm	984 / 984 / 787	984 / 984 / 787
Cutting feedrate (X / Y / Z)ipm	ipm	0.039 ~ 394	0.039 ~ 394
Motor
Feed axis motor (X / Y / Z)HP	HP	2.5 / 2.5 / 2.5 [Fanuc : 4.0 / 4.0 / 4.0]	2.5 / 2.5 / 2.5 [Fanuc : 4.0 / 4.0 / 4.0]
Spindle cooler (50 / 60 Hz)HP	HP	0.5	0.5
ATC
Tool shank		BT-30	BT-30
Pull stud		MAS P40T-1 (45°)	MAS P40T-1 (45°)
Tool storage capacityea	ea	16	16
Max tool diameterin	in	Ø0.63	Ø0.63
Max tool lengthin	in	7.9	7.9
Max tool weightlb	lb	7	7
Tool selection		Fixed Address	Fixed Address
Power source
Electric power supplykVA	kVA	25	25
Power specification		380V, 60Hz [FANUC : 220V, 60Hz]	380V, 60Hz [FANUC : 220V, 60Hz]
Compressed air (pressure x consumption)		73~102 psi x 690Nℓ/min	73~102 psi x 690Nℓ/min
Tank capacity
Lubricationgal	gal	0.5	0.5
Machine size
Heightin	in	92.9 ~ 108.7	92.9 ~ 108.7
Floor space (L x W)in	in	96.9 x 108.5 [Full Cover : 105.9 x 105.1]	96.9 x 108.5 [Full Cover : 105.9 x 105.1]
Weightlb	lb	11,023	11,023
NC controller
NC controller		SIEMENS-828D (Opt.: FANUC 0i-MF)	SIEMENS-828D (Opt.: FANUC 0i-MF)

Specifications from the manufacturer, converted from metric. Confirm the configuration on your quote.

Downloads

Request a quote

Send the details and we will price the Hi-M1300 with freight, rigging and the options you need.

Before you order: what your shop needs ready and the 2026 Section 179 rules

Call sales(817) 472-5178