Eurotech Trofeo BMX
11-axis double-turret turn/mill center
Built to order. Ask for lead time.
Overview
Two 15-station direct-drive turrets, two Y-axes, bar up to 3.15 in
The Trofeo BMX is the next generation of Eurotech's Trofeo series, a double-spindle, double-turret bar machine built to finish complex parts in one setup. Both 15-station turrets have a built-in motor that drives the live tools directly, 20 hp at up to 10,000 rpm, and each turret has its own Y-axis. The 51, 70 and 80 share a 10.6 in max machining diameter and 25.2 in machining length, and differ in bar capacity (2.0, 2.75 and 3.15 in) and main spindle nose (ASA 5, 6 and 8). It runs on a FANUC 31i-B Plus control with Eurotech's own software.
Guide: Twin-turret or single-turret lathe: what do more turrets add?
At a glance
- Bar capacity
- 2.0 to 3.15 in
- Main spindle
- 3,500 to 5,000 rpm, 34 to 54 HP
- Turrets
- 2 x 15 stations, all 30 live
- Axes
- 11
- Control
- FANUC 31i-B Plus
Features
01Direct-drive live tooling at every stationEach turret has a built-in motor that powers the live tools directly instead of through belts or gears. Live tools run up to 10,000 rpm with 20 hp and 47.7 Nm, and all 15 stations on both turrets are live, so cross drilling, milling, rigid tapping, polygon milling and gear hobbing can run from either turret. Indexing takes 0.15 seconds and goes the short way around.
02Two-axis sub-spindle, three tools in the cutThe sub-spindle moves in Z3 and X3 and can be offset from the main spindle, which removes interference between the two turrets. With superimposition, three tools cut at once. Eurotech's ClearShift lets the upper and lower turrets be programmed independently, so parts come off the sub-spindle without stopping the cut.
03Programmable gantry and dual conveyorThe parts gantry runs on a CNC axis and pulls finished parts or remnants from the main or sub-spindle while tools are still cutting. It rotates 180 degrees to drop both, and the two conveyors are programmed separately so parts and remnants land in different bins.
04FANUC 31i-B Plus with Eurotech software15 in iHMI touch screen with Manual Guide and direct DXF import. Eurotech adds Gap Elimination Logic to remove forced dwells between turning, C-axis and Y-axis moves, plus tool life management, stress load monitoring, a closed-loop sub-spindle ejection check and a programmable tool probe on each turret.
- 05Up to 240 tools with EGSThe two 15-station turrets give 30 stations. With the Eurotech Gang Tool System and the true Y-axis on each turret, the machine supports up to 240 cutting tools, which cuts down tool changes between jobs.
- 06Slant bed with box ways on X and YThe 45 degree cast-iron slant bed carries roller guideways on Z and box-type guideways on X and Y. Main and sub-spindle are liquid-cooled built-in motor spindles with glass scales.
Video
Trofeo BMX 70-SY2, multi-axis turning step by step
Specifications
| Item | Trofeo BMX series | |||
|---|---|---|---|---|
| Trofeo BMX 51-SY2 | Trofeo BMX 70-SY2 | Trofeo BMX 80-SY2 | ||
| Machining capacity | ||||
| Bar capacitymm/inches | mm/ | 51/ | 70/ | 80/ |
| Max. machining diameterin | in | 10.6 | 10.6 | 10.6 |
| Max. machining lengthin | in | 25.2 | 25.2 | 25.2 |
| Max. swing over diameterin | in | 10.6 | 10.6 | 10.6 |
| Main spindle | ||||
| Max. speedrpm | rpm | 5000 | 4500 | 3500 |
| Spindle noseASA | ASA | 5" | 6" | 8" |
| Spindle borein | in | 2.3 | 3.03 | 3.6 |
| Inside diam. of bearingsin | in | 3.5 | 4.3 | 5.1 |
| Chuck diameterin | in | 6.5 / | 8.3 / | 8.3 / |
| Motor powerHP | HP | 34 | 54 | 34 |
| Max. torquelb-ft | lb-ft | 80 / | 188 / | 325 / |
| C-axis: min. programmable value° | ° | 0.001 | 0.001 | 0.001 |
| Sub-spindle | ||||
| Max. speedrpm | rpm | 5000 | 5000 | 5000 |
| Spindle noseASA | ASA | 5" | 5" | 5" |
| Spindle borein | in | 2.3 | 2.3 | 2.3 |
| Drawtube inside diameterin | in | 2 | 2 | 2 |
| Inside diam. of bearingsin | in | 3.5 | 3.5 | 3.5 |
| Chuck diameterin | in | 6.5 / | 6.5 / | 6.5 / |
| Motor powerHP | HP | 23 / | 23 / | 23 / |
| Max. torquelb-ft | lb-ft | 80 / | 80 / | 80 / |
| C-axis: min. programmable value° | ° | 0.001 | 0.001 | 0.001 |
| Upper turret (1), lower turret (2) | ||||
| No. of stations / max no. of toolsN° | N° | 30/ | 30/ | 30/ |
| No. of live tools / max no. of live toolsN° | N° | 30/ | 30/ | 30/ |
| Turret indexing (1 pos)sec | sec | 0.15 | 0.15 | 0.15 |
| Live tool max. speedrpm | rpm | 10,000 | 10,000 | 10,000 |
| Live tool motor powerHP | HP | 20 | 20 | 20 |
| Live tool max. torquelb-ft | lb-ft | 35 | 35 | 35 |
| X1-X2 axis: stroke - rapid traverseinch / IPM | inch / | 7-710 | 7-710 | 7-710 |
| Z1-Z2 axis: stroke - rapid traversemm / m/min | mm / | 640-540 - 30 | 640-540 - 30 | 640-540 - 30 |
| Y1-Y2 axis: stroke - rapid traversemm / m/min | mm / | 90 - 9 | 90 - 9 | 90 - 9 |
| Cooling system | ||||
| Tank capacitygal | gal | 132 | 132 | 132 |
| Power rating of 3 electropumpsHP | HP | 5 | 5 | 5 |
| Dimensions and weight | ||||
| Machine with swarf conveyorin | in | 209 x 88 x 94 H | 209 x 88 x 94 H | 209 x 88 x 94 H |
| Spindle centre heightin | in | 50 | 50 | 50 |
| Machine weight with swarf conveyorlb | lb | 23,810 | 24,250 | 24,912 |
Request a quote
Send the details and we will price the Trofeo BMX 51 / 70 / 80-SY2 with freight, rigging and the options you need.
Before you order: what your shop needs ready and the 2026 Section 179 rules
Call sales(817) 472-5178Related machines
- Eurotech Rapido BMX10-axis double-turret turn/mill center
- Eurotech Ultima B620Single-turret turn/mill center with Y-axis and sub-spindle
- Eurotech StallionLarge single-turret turn/mill center with Y-axis and sub-spindle
- Eurotech Multipla13-axis, three-turret twin-spindle turn/mill center
- Eurotech Xtreme8-axis Swiss-type lathe with C-axis main and sub-spindle and Y2
- Eurotech Kobra7-axis hybrid Swiss-type lathe, Y2 available on all models
- Eurotech Gepard7-axis hybrid Swiss-type lathe
- Eurotech Diamont10-axis hybrid Swiss-type lathe with turret
